ElomIlomHelp < CmsTier3

<!-- keep this as a security measure:
   #uncomment if the subject should only be modifiable by the listed groups 
   * Set ALLOWTOPICCHANGE = Main.TWikiAdminGroup,Main.CMSAdminGroup
   * Set ALLOWTOPICRENAME = Main.TWikiAdminGroup,Main.CMSAdminGroup
   #uncomment this if you want the page only be viewable by the listed groups
   #* Set ALLOWTOPICVIEW = Main.TWikiAdminGroup,Main.CMSAdminGroup,Main.CMSAdminReaderGroup
-->

---+ !!Interacting with the ELOM/ILOM

ELOM is the older version of the service processor's firmware while ILOM is the name of the current versions.

   * [[http://www.zagbot.com/solaris.html][nice reference sheet by zagbot]]

%TOC%

---++ILOM

The following is valid for version
<pre>
SP firmware 2.0.2.6
SP firmware build number: 35128
SP firmware date: Mon Jul 28 10:17:35 PDT 2008
SP filesystem version: 0.1.16
</pre>

---+++ Show the status of the running system

This will also print whether the system is on or off.
<pre>
show /SYS
</pre>

---+++ Starting/stopping system

<pre>
start /SYS
stop /SYS
stop -force /SYS
reset /SYS
</pre>

---+++ Viewing the SP logs

Many important things in respect to HW are recorded in the Service Processor logs
<pre>
show /SP/logs/event/info
</pre>
Alternatively look at the [[https://wiki.chipp.ch/twiki/bin/view/CmsTier3/IpmiHelp#Retrieve_event_logs][ipmitool command]] for the same purpose.

---+++ Preparing to remove a component (e.g. removing a blade from enclosure)

The =prepare_to_remove_action= of the component should show a =ready= status. This is also reflected by a blue LED lighting up on the blade server.

For taking out a blade from a blade center, after shutting down the OS, log in to the blade's ILOM and execute
<pre>
set /SYS prepare_to_remove_action=true
 </pre>

---+++ Rebooting the SP
This will shut down the connection to the /SP console
<pre>
reset /SP
</pre>
---+++ Reading out temperature sensors with ILOM

<pre>
show /SYS/MB/T_AMB0
...
show /SYS/MB/T_AMB3
show /SYS/T_AMB
show /SYS/PS0/T_AMB
show /SYS/PS1/T_AMB
</pre>

---+++ starting the console redirection
<pre>
start /SP/console
</pre>


---+++ Rebooting the SP
<pre>
reset /SP
</pre>

---+++ show SP network settings

<pre>
show /SP/network
</pre>

---+++ Show SP serial connection settings
<pre>
show /SP/serial/host

 /SP/serial/host
    Targets:

    Properties:
        commitpending = (Cannot show property)
        flowcontrol = none
        pendingflowcontrol = none
        pendingspeed = 9600
        speed = 9600
</pre>

Set the serial port settings for terminal access
<pre>
set /SP/serial/host pendingspeed=57600 commitpending=true
</pre>

---+++ List various sensors and obtain hardware information

---++++ clock  (also how to set it)

<pre>
show /SP/clock
    Properties:
        datetime = Mon May 25 08:17:48 2009
        usentpserver = disabled
</pre>

<pre>
# setting to 2009-05-25 09:26
set /SP/clock/   datetime=052509262009
</pre>

---++++ Power supplies

<pre>
show /SYS/PS2/PWROK
    Properties:
        type = Power Supply
        class = Discrete Sensor
        value = Disabled
</pre>

---++++ Processor Board

<pre>
show /SYS/PROC
    Targets:
        P0
        P1
        V_+1V8
        BAT
        NET0
        NET1
        FRONT_T_AMB
        REAR_T_AMB

    Properties:
        type = Processor Board
        board_part_number = 501-7641-02
        board_serial_number = 0060HSV-0818001205
        board_product_name = ASSY,CPU,NO OPTERON,X4500
</pre>

---++++ CPUs
<pre>
show /SYS/PROC/P0
    Targets:
        T_CORE
        V_+1V25
        V_+1V5
        V_+2V5
        FAIL
        D0
        D1
        D2
        D3

    Properties:
        type = Host Processor
        product_name = DUAL CORE AMD OPTERON(TM) PROCESSOR 290
        product_manufacturer = ADVANCED MICRO DEVICES
        product_version = 02
        product_part_number = 0F21
        product_serial_number = (none)
</pre>

---++++ DIMMs
ILOM 3.x
<pre>
show /SYS/MB/MCH/DA0/SERVICE
   Properties:
        type = Indicator
        ipmi_name = MB/MCH/DA0/SVC
        value = On         # "On" indicates that this DIMM (A0) has a problem
</pre>

ILOM 2.x
<pre>
show /SYS/PROC/P0/D0
    Properties:
        type = DIMM
        product_name = 2048MB DDR 400 (PC3200) ECC
        product_manufacturer = QIMONDA
        product_version = 130C
        product_part_number = 72D256320HBR5C
        product_serial_number = 06036C24
</pre>

---++++ Ethernet controllers

<pre>
show /SYS/PROC/NET0
    Properties:
        type = Network Interface
        product_name = DUAL PORT GIGABIT ETHERNET CONTROLLER (COPPER)
        product_manufacturer = INTEL
        product_version = (none)
        product_part_number = 82546EB
        product_serial_number = %RED%hidden%ENDCOLOR%
</pre>

---++++ Processor board front and rear temperatures

<pre>
show /SYS/PROC/FRONT_T_AMB
    Properties:
        type = Temperature
        class = Threshold Sensor
        value = 16.000 degree C
        upper_nonrecov_threshold = 100.00 degree C
        upper_critical_threshold = 95.00 degree C
        upper_noncritical_threshold = 90.00 degree C
        lower_nonrecov_threshold = 0.00 degree C
        lower_critical_threshold = 0.00 degree C
        lower_noncritical_threshold = 0.00 degree C

-> show /SYS/PROC/REAR_T_AMB
    Properties:
        type = Temperature
        class = Threshold Sensor
        value = 18.000 degree C
        upper_nonrecov_threshold = 100.00 degree C
        upper_critical_threshold = 95.00 degree C
        upper_noncritical_threshold = 90.00 degree C
        lower_nonrecov_threshold = 0.00 degree C
        lower_critical_threshold = 0.00 degree C
        lower_noncritical_threshold = 0.00 degree C
</pre>

---++ ELOM
---+++ Reading out temperature sensors with ELOM

<pre>
show /SYS/Temperature/CPU_0_Temp
show /SYS/Temperature/CPU_1_Temp
show /SYS/Temperature/Ambient_Temp0
</pre>

---++ Accessing the SP's embedded Linux

The ILOM is run by a custom Linux on the service processor. It is possible to access it by logging using the *sunservice* account:

<pre>
ssh sunservice@mangm-interface
</pre>

Note that SUN has placed the following warning as login message:
<pre>
WARNING: The "sunservice" account is provided solely to allow
Sun Services to perform diagnosis and recovery tasks. Customer use of
the "sunservice" account may interfere with the correct operation of
ILOM and is not supported other than to perform recovery procedures as
documented by Sun Microsystems. Normal ILOM operations should always be
performed using the root account. Further usage of the "sunservice"
account implies your agreement with these terms.
</pre>

---++ Blade Center Chassis

---+++ ILOM network configuration

MAC addresses of the blade enclosures were given in the delivery notes coming with the hardware. Configure the dhcp server to assign an IP to this address.
Then log into the chassis ILOM.

The chassis network information can be listed through
<pre>
show /CH/CMM/NET0
</pre>

Finding each blade servers' MAC address (here for blade server 0):
<pre>
show /CH/BL0/SP/network

    Properties:
        type = Network Configuration
        commitpending = (Cannot show property)
        ipaddress = 192.168.2.100
        ipdiscovery = dhcp
        ipgateway = 192.168.2.21
        ipnetmask = 255.255.255.0
        macaddress = 00:21:28:57:13:E0
        pendingipaddress = 0.0.0.0
        pendingipdiscovery = dhcp
        pendingipgateway = 0.0.0.0
        pendingipnetmask = 0.0.0.0
        outofbandmacaddress = %BLUE%00:21:28:57:13:E0%ENDCOLOR%
        sidebandmacaddress = 00:21:28:57:13:E1
        managementport = /SYS/SP/NET0
        pendingmanagementport = /SYS/SP/NET0
</pre>

---+++ Listing Server Firmware version from the Chassis ILOM

<pre>
-> show /CH/BL0
...
    Properties:
        type = Blade
        ipmi_name = BL0
...
        fru_extra_1 = FW 3.0.6.21
...
</pre>

-- Main.DerekFeichtinger - 31 Oct 2008
   * [[%ATTACHURL%/819-4363-12.pdf][819-4363-12.pdf]]: Sun Fire™ X4500/X4540 Servers Diagnostics Guide
Attachments
Topic attachments
I	Attachment	History	Action	Size	Date	Who	Comment
pdf	819-4363-12.pdf	r1	manage	4771.9 K	2012-12-28 - 10:10	FabioMartinelli	Sun Fire™ X4500/X4540 Servers Diagnostics Guide
This topic: CmsTier3 > WebHome > AdminArea > ElomIlomHelp
Topic revision: r16 - 2012-12-28 - FabioMartinelli